Difference between revisions of "Basic commands"
From Tech-Wiki
| (5 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
[[Category:Fortinet]] | [[Category:Fortinet]] | ||
| + | |||
| + | Basic system information - Equivalent to cisco ‘show version’ | ||
| + | get sys status | ||
| + | get sys performance status | ||
Essentials troubleshooting commands: | Essentials troubleshooting commands: | ||
| Line 10: | Line 14: | ||
List network interfaces - Equivalent to cisco ‘show ip interfaces brief’ | List network interfaces - Equivalent to cisco ‘show ip interfaces brief’ | ||
diag ip address list | diag ip address list | ||
| + | get sys interface physical | ||
| + | get hardware nic port1 | ||
| + | diag hard deviceinfo nic port1 | ||
| + | get system interface transceiver port1 | ||
| + | fnsysctl ifconfig port1 | ||
List the routing table - Equivalent to cisco ‘show ip route’ | List the routing table - Equivalent to cisco ‘show ip route’ | ||
| Line 17: | Line 26: | ||
Connect to a specific VDOM (change context) | Connect to a specific VDOM (change context) | ||
config vdom | config vdom | ||
| − | edit root (or edit vdom1) | + | edit root (or edit vdom1, or config global) |
Sample network configuration with physical ports and vlans: | Sample network configuration with physical ports and vlans: | ||
| Line 48: | Line 57: | ||
diag netlink brctl name host <vdom.name>.b | diag netlink brctl name host <vdom.name>.b | ||
| − | + | Listing a firewall rule | |
| − | + | show firewall policy 6 | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | Disable the ‘more’ at page breaks | |
| − | + | config sys console | |
| − | + | set output standard | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
Latest revision as of 18:47, 2 December 2020
Basic system information - Equivalent to cisco ‘show version’
get sys status get sys performance status
Essentials troubleshooting commands:
exec ping <destination> exec ping-options source <origin> exec ping6 exec traceroute <destination> exec telnet|ssh <destination>
List network interfaces - Equivalent to cisco ‘show ip interfaces brief’
diag ip address list get sys interface physical get hardware nic port1 diag hard deviceinfo nic port1 get system interface transceiver port1 fnsysctl ifconfig port1
List the routing table - Equivalent to cisco ‘show ip route’
get router info routing-table all diag ip route list
Connect to a specific VDOM (change context)
config vdom edit root (or edit vdom1, or config global)
Sample network configuration with physical ports and vlans:
config system interfaces edit port2 set ip 163.7.131.4 255.255.255.248 set vdom root end edit vlan.15 set interface port5 set vlanid 15 set ip 163.7.131.4 255.255.255.248 set vdom root end
Setting static routes and default gateway
config router static edit 1 set dst 0.0.0.0/0.0.0.0 set gateway 192.168.0.254 set device vlan.15 end
Show arp table
diag ip arp list
Show arp table (in transparent mode)
diag netlink brctl list diag netlink brctl domain <bridge_name> diag netlink brctl name host <vdom.name>.b
Listing a firewall rule
show firewall policy 6
Disable the ‘more’ at page breaks
config sys console set output standard