Difference between revisions of "Useful commands"
From Tech-Wiki
| (14 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
[[Category:Palo Alto]] | [[Category:Palo Alto]] | ||
| − | Executing ping: | + | Executing ping/traceroute: |
ping host xxx.xxx.xxx.xxx | ping host xxx.xxx.xxx.xxx | ||
| + | traceroute host xxx.xxx.xxx.xxx | ||
| − | + | To get interfaces and MAC address: | |
| − | + | show interface all | |
| + | show arp all | ||
| + | |||
| + | Display routing table: | ||
| + | show routing route | ||
Getting system information: | Getting system information: | ||
show system info | show system info | ||
| − | show system | + | show system logdb-quota |
Getting performance status: | Getting performance status: | ||
| − | show system statistics session | + | show system statistics session (Throughput) |
| − | show system resources | + | show system resources (Top equivalent) |
| − | show running resource-monitor | + | show running resource-monitor (Historical) |
| − | + | Sample log filter examples to use in GUI: | |
| − | + | (addr.src in 192.168.1.10) and (port.dst eq 21) | |
| + | (from/member eq 'trust') and (source/member eq 'Host1') | ||
| − | + | Reading the system log: | |
| − | + | less mp-log master.log | |
| − | + | ||
Validate if specified traffic will match any firewall/nat rule | Validate if specified traffic will match any firewall/nat rule | ||
| Line 28: | Line 33: | ||
To view current host objects based on FQDN or to update the list: | To view current host objects based on FQDN or to update the list: | ||
| + | show dns-proxy fqdn all | ||
request system fqdn show | request system fqdn show | ||
request system fqdn refresh force yes | request system fqdn refresh force yes | ||
| Line 34: | Line 40: | ||
show session all filter state active | show session all filter state active | ||
show session id xxxxx | show session id xxxxx | ||
| + | |||
| + | Filtering and closing active connections: | ||
| + | show session all filter source x.x.x.x | ||
| + | show session all filter application xxxxxx | ||
| + | clear session id xxxxx | ||
| + | |||
| + | Change the virtual system | ||
| + | set system setting target-vsys ? | ||
To commit the candidate version of configuration: | To commit the candidate version of configuration: | ||
| Line 43: | Line 57: | ||
To validate if the candidate version is consistent (validating syntax and semantics): | To validate if the candidate version is consistent (validating syntax and semantics): | ||
| − | validate full | + | > configure |
| + | # validate full | ||
| + | > show jobs id xxxx | ||
To commit even with errors: | To commit even with errors: | ||
| Line 54: | Line 70: | ||
less mp--log ikemgr.log | less mp--log ikemgr.log | ||
| − | + | Reboot/Shutdown the device | |
| − | + | request restart/shutdown system | |
| − | + | On GUI click on Device tab > Setup link > Operations tab | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
Latest revision as of 21:22, 25 May 2021
Executing ping/traceroute:
ping host xxx.xxx.xxx.xxx traceroute host xxx.xxx.xxx.xxx
To get interfaces and MAC address:
show interface all show arp all
Display routing table:
show routing route
Getting system information:
show system info show system logdb-quota
Getting performance status:
show system statistics session (Throughput) show system resources (Top equivalent) show running resource-monitor (Historical)
Sample log filter examples to use in GUI:
(addr.src in 192.168.1.10) and (port.dst eq 21) (from/member eq 'trust') and (source/member eq 'Host1')
Reading the system log:
less mp-log master.log
Validate if specified traffic will match any firewall/nat rule
test security-policy-match from trust to untrust source 10.4.70.48 destination 200.1.2.100 destination-port 80 protocol 6 test nat-policy-match source 10.1.0.1 destination 200.1.2.100 destination-port 21 protocol 6
To view current host objects based on FQDN or to update the list:
show dns-proxy fqdn all request system fqdn show request system fqdn refresh force yes
Display current connections through the firewall and get detailed info for a specific one:
show session all filter state active show session id xxxxx
Filtering and closing active connections:
show session all filter source x.x.x.x show session all filter application xxxxxx clear session id xxxxx
Change the virtual system
set system setting target-vsys ?
To commit the candidate version of configuration:
commit partial vsys vsys1 device-and-network excluded
Check pending changes:
Click on the Device tab > Config audit Select a candidate config on the right
To validate if the candidate version is consistent (validating syntax and semantics):
> configure # validate full > show jobs id xxxx
To commit even with errors:
commit force
Troubleshoot IPSec VPN issues:
show vpn gateway show vpn ike-sa debug ike global on debug less mp--log ikemgr.log
Reboot/Shutdown the device
request restart/shutdown system On GUI click on Device tab > Setup link > Operations tab